摘要：<span style="font-family:宋體;">西安不銹鋼板折彎加工注意事項</span> <p class="MsoNormal"> <span style="font-family:宋體;">西安華達不銹鋼有限公司是專業加工不銹鋼的企業</span><span>,</span><span style="font-family:宋體;">公司在嚴謹、務實、高效、精益的發展理念指導下飛速發展</span><span>,</span><span style="font-family:宋體;">引進了的技術和設備</span><span>,</span><span style="font-family:宋體;">并擁有成套設備生產線等</span><span>,</span><span style="font-family:宋體;">為公司的持續發展</span> <span style="font-family:宋體;">奠定了堅實的基礎</span><span>.</span><span style="font-family:宋體;">下面介紹一下不銹鋼折彎加工注意事項</span><span>:</span> </p> <p class="MsoNormal"> <span style="font-family:宋體;">1、</span><span style="font-family:宋體;">單位尺寸下</span><span>,</span><span style="font-family:宋體;">板材越厚</span><span>,</span><span style="font-family:宋體;">所需折彎力越大</span><span>,</span><span style="font-family:宋體;">而且隨著板厚增大在選擇折彎設備時折彎力的裕量應該更大</span><span>,</span><span style="font-family:宋體;">不銹鋼因?qū)嵝员绕胀ǖ吞间摬?lt;/span><span>,</span><span style="font-family:宋體;">延伸率低</span><span>,</span><span style="font-family:宋體;">導致所需變形力大</span><span>;</span> </p> <p class="MsoNormal"> <span>2、</span><span style="font-family:宋體;">單位尺寸下</span><span>,</span><span style="font-family:宋體;">抗拉強度越大</span><span>,</span><span style="font-family:宋體;">延伸率越小</span><span>,</span><span style="font-family:宋體;">所需折彎力越大</span><span>,</span><span style="font-family:宋體;">折彎角應該越大</span><span>,</span><span style="font-family:宋體;">相對于碳鋼相同板厚的不銹鋼折彎角較大</span><span>,</span><span style="font-family:宋體;">這一點應特別注意否則會出現壓彎裂紋</span><span>,</span><span style="font-family:宋體;">影響工件強度</span><span>;</span> </p> <p class="MsoNormal"> <span>3、</span><span style="font-family:宋體;">設計圖中板厚與折彎半徑對應情況下</span><span>,</span><span style="font-family:宋體;">根據經驗</span><span>,</span><span style="font-family:宋體;">一道彎工件的展開尺寸為直角邊相加減去兩個板厚</span><span>,</span><span style="font-family:宋體;">完全可以滿足設計精度要求</span><span>,</span><span style="font-family:宋體;">根據經驗公式計算展開量可簡化計算過程大大提高生產效率</span><span>;</span> </p> <p class="MsoNormal"> <span>4、</span><span style="font-family:宋體;">材質的屈服強度越大</span><span>,</span><span style="font-family:宋體;">彈性回復量就越大</span><span>,</span><span style="font-family:宋體;">為獲得折彎件</span><span>9 0</span><span style="font-family:宋體;">度的角度</span><span>,</span><span style="font-family:宋體;">所需壓刀的角度就要設計的越小</span><span>,</span><span style="font-family:宋體;">奧氏體不銹鋼在折彎時相對于碳鋼存在較大彈性回復變形</span><span>,</span><span style="font-family:宋體;">所以壓刀角度相對碳鋼要小</span><span>.</span> </p> <span style="font-family:宋體;">公司至成立以來，以“誠信、合作、雙贏、發展”為經營宗旨，堅持“價格**、用戶、信譽”的營銷理念，在市場上獲得了良好的口碑。</span> <p class="MsoNormal"> <span style="font-family:宋體;"></span><span>&nbsp;&nbsp; </span><span style="font-family:宋體;"></span><span>029</span><span style="font-family:宋體;">—</span><span>88633755</span> </p> <p class="MsoNormal"> <span style="font-family:宋體;">詳情參考：</span><span><a href="http://wuyitex.com/">http://wuyitex.com</a></span> </p> <p class="MsoNormal"> <span></span>&nbsp; </p>